基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。     

Novel Bi-Doped Amorphous SnOx Nanoshells for Efficient Electrochemical CO2 Reduction into Formate at Low Overpotentials

Engineering novel Sn-based bimetallic materials could provide intriguing catalytic properties to boost the electrochemical CO₂ reduction. Herein, the first synthesis of homogeneous Sn_1−xBi_x alloy nanoparticles (x up to 0.20) with native Bi-doped amorphous SnO_x shells for efficient CO₂ reduction is reported. The Bi-SnO_x nanoshells boost the production of formate with high Faradaic efficiencies (>90%) over a wide potential window (−0.67 to −0.92 V vs RHE) with low overpotentials, outperforming current tin oxide catalysts. The state-of-the-art Bi-SnO_x nanoshells derived from Sn_0.80Bi_0.20 alloy nanoparticles exhibit a great partial current density of 74.6 mA cm⁻² and high Faradaic efficiency of 95.8%. The detailed electrocatalytic analyses and corresponding density functional theory calculations simultaneously reveal that the incorporation of Bi atoms into Sn species facilitates formate production by suppressing the formation of H₂ and CO.     

一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.     

全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

一例带电水冲洗触发的220kV避雷器爆炸事故分析

对一例220 kV金属氧化物避雷器在带电水冲洗后发生爆炸故障的原因进行了分析。通过对完好避雷器和故障避雷器进行解体和对比分析,发现故障避雷器下节顶部压力释放装置内部的密封胶圈发生凹陷变形。最后,对该类事故提出预防措施。     

高氯酸铵含量对高铝富燃料推进剂中重要组分高氯酸铵/铝 一次燃烧性能和铝粉团聚的影响

采用CO2激光点火装置联合高速摄影系统及扫描电子显微镜等凝聚相燃烧产物分析技术，研究了高氯酸铵(AP)含量对高Al富燃料推进剂中重要组分AP/Al一次燃烧过程中燃烧现象、引燃时间、燃烧扩散时间、燃尽时间、燃烧效率、颗粒团聚及凝聚相燃烧产物的表面形貌、粒径及其分布的影响。结果表明，各AP/Al混合粉体的燃烧过程均可分为表面引燃、燃烧扩散和火焰熄灭3个阶段，但各样品在不同燃烧阶段的燃烧现象存在明显差异。AP含量由10wt%增至30wt%，样品燃烧剧烈程度增强，燃烧过程中固相颗粒的溅射现象越加明显；在火焰熄灭阶段，各样品燃烧由以停留在样品燃面处的燃烧为主逐渐变为以溅射颗粒的燃烧为主，且随反应进行，燃面已燃固相颗粒最先熄灭，各样品表面引燃时间、燃烧扩散时间、燃烧持续时间均缩短，即燃烧反应速率逐渐加快。在AP/Al混合物中，铝粉的燃烧效率、凝聚相燃烧产物粒度及其团聚程度随AP含量增加而增加。     

干燥机托轮位置的分析及调整

针对化纤厂干燥机系统运行中出现的转动筒体的位置调整,通过对干燥机托轮和轮带的受力分析以及托轮位置的具体调整方法,从根本上解决了影响干燥机运行中的问题,收到了良好的效果,达到了设备运行要求,提高了设备运行周期,保证了装置平稳运行。